Autowatch Ghost Immobiliser Installation
The Ghost is the most advanced aftermarket in the UK. immobiliser for CAN bus. It's discrete, doesn't employ keys or LEDs and is hidden within the wiring of the vehicle.
The user can also disable the system temporarily using Transport Mode when renting their vehicle. This guide will take you through the installation process of a Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser protects your car from key hacking attacks, cloning and relay attacks. The system connects directly to your vehicle's ECU and is protected by a unique pin code that you choose. It is not detected by thieves using diagnostic scanners or other advanced methods. It isn't able to be disabled with circuit cuts.
The system is simple to use, however professional installation is recommended to ensure a smooth connection with the ECU of your vehicle. Installers who are approved by Thatcham can assist with the installation and programing of your Ghost system. They can also recommend a tracking or alarm system to complete the security package for your vehicle.
To avoid the accidental deployment of airbags or short circuits, the installer must first disconnect your battery. Once the battery is disconnected, the installer may be able to work safely. Basic hand tools can be used to ensure precise connections. A multimeter is useful to test electrical values. Cable tie and insulation tape are crucial to ensure connections are secure and keep wiring neat. In addition, the user's manual provides specific guidance specifically tailored to your Ghost Immobiliser model.
It is essential to choose a grounding location that is free of paint or debris during installation. Installers should also make sure that the immobiliser's wires CAN H and can L are connected to the appropriate ECU ports. These wires can be plugged into or soldered depending on the model. Using immobiliser ghost -quality connector is recommended to ensure a long-lasting and reliable connection.
Once the installation is complete Once the installation is completed, the customer can enable Transport Mode. This allows the vehicle to be used by valet parking or mechanics without needing to know the pin code. The customer has to press the service icon on the dashboard five times over two seconds. After that the system will verify with 5 signal indicators.
The Autowatch Ghost 2 immobiliser is TASSA approved and a highly efficient immobiliser. It's a smart option for anyone who regularly rents their vehicle through platforms such as Turo. An immobiliser can reduce the cost of insurance, as it decreases the likelihood of theft.
Getting Started
If you are looking for a solution that will safeguard your vehicle from theft, you can't go wrong with an autowatch ghost immobiliser. It will stop your car from starting even if a criminal steals or copies the key. It's possible due to its advanced technology that stops the engine from starting until the correct PIN code has been entered.
The device connects to the vehicle's bus network CAN, allowing direct communication with the ECU. It makes use of the buttons on your dashboard and steering to create a unique sequence which only you know. This makes it impossible for anyone else to start your car. This is the best way to safeguard your pride and joy. It will not lose its value in the event that you decide to sell it.
Installing a Ghost immobiliser is easy however, you must follow the instructions to avoid electrical problems and malfunctions of the system. First, you need to locate and identify a constant 12V power source as well as an appropriate grounding point on the vehicle's chassis. After that, you can begin to connect the wires for the immobiliser. Make sure to use high-quality connectors and soldering methods to ensure a strong connection. Also, make sure to protect the connections by insulating them with heat shrink tubing and insulation tape to protect them from short circuits in electrical power and other issues.
Once ghost immobiliser review are connected, you can plug in the battery and start the engine to test if the immobiliser is working. Once everything is working properly then you can put it in a secure place under the dash or somewhere else in the vehicle. Make sure you hide it well to prevent any thief from taking advantage of it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified this means it complies with the highest standards of security and is a great protection against car thieves. It is impervious to key cloning and hacking and cannot be disabled without a code. It is simple to use, and it can be set to a service valet setting so that your vehicle won't be activated when you take it for an MOT or service.
Wiring
The Ghost Immobiliser is a cutting-edge security system specifically designed to deter theft of vehicles. It connects directly to your vehicle's CAN bus and communicates with the ECU, making it virtually undetectable as an addition to your vehicle. Ghost Immobiliser doesn't interfere with your vehicle's factory settings unlike other aftermarket systems which require the removal of circuit elements.
It's also completely undetectable to thieves using diagnostic scanners. The system doesn't transmit or receive radio frequency signals, but instead uses CAN data to communication with your ECU. It also doesn't require modifications to your current key fobs.
Enter the sequence to disarm (either two or one buttons) and then switch on the ignition in your car to activate Ghost Immobiliser. The indicator will flash two times to confirm that you have entered the correct code. After this, you can start your car and drive away with peace of mind.
Once installed Once installed, the Ghost Immobiliser will protect your car from hacking and key cloning and will also protect the value of your pride and joy. In Transport Mode, you can temporarily disable the Ghost Immobiliser when you need to give your vehicle to service or valet parking.
To complete the Ghost Immobiliser installation, you'll have to find the source of power that is constant (12V) and an earthing point. Ensure that these are both well-insulated and safe to touch. Cable ties are also recommended for bundling and securing the wires. This will reduce the chance of theft by thieves. Make sure you double-check the location of these points to avoid mistakes and mark them with a piece of tape or label. It's important to check every connection for signs of wear and tear. Be sure to ensure that all connections are securely in place, and properly sealed. Don't forget to test the Ghost Immobiliser after the installation is completed. This will ensure that the unit functions properly and that all connections and insulation are secure. Be sure to correct any issues as soon as they arise.
Testing
The Autowatch Ghost immobiliser is a revolutionary vehicle security system that connects seamlessly with your vehicle's ECU to prevent unauthorized motor starting. Its cutting-edge technology protects your vehicle against key cloning and hacking as well as other methods commonly used by thieves to steal vehicles. The Ghost also works in tandem with existing alarm and tracking systems to offer the best protection for your vehicle. This system's unmatched features and discreet design make it a popular choice for car enthusiasts and security-conscious drivers too.
It is crucial to follow the steps of installation to ensure the correct integration of the Ghost Immobiliser. The best way to begin is to refer to the wiring diagram of your vehicle that serves as a guideline to locate and connecting the required wires. The next step is to determine the power and grounding sources. Once you've identified these you'll have to mark them in a way that they are easy to locate during the installation process. Finally, it's essential to use high-quality tools and materials. Basic hand tools will aid in making precise connections. A multimeter will verify electrical values, and also ensure safety. Cable ties and insulation tape will keep the connections tidy and neat. Finally, a user manual will provide specific instructions specific to your Ghost model.
Before proceeding with the installation, it's important to test the system by entering the PIN code and then starting the vehicle. This step will confirm that the immobiliser works as intended, preventing unauthorised vehicle start-ups. It's recommended to perform this routinely as part of your regular inspections of the vehicle to ensure the system is operating correctly.
After the installation has been completed, you can begin driving your car with confidence. The Ghost will protect your car from potential car thieves. It will ensure that no one can drive away with your vehicle without having the correct PIN code. The Ghost can be used in conjunction with an approved Thatcham tracker, which detects attempts at theft or tampering. This will allow you to track your vehicle if it is stolen.
The Ghost can be utilized in a variety of vehicles and is compatible with the majority of major manufacturers. Monty's Locksmith can assist you in securing your vehicle with this innovative device. Contact us today to find out more about our services and installation options. We are a TASSA registered installer, a certificate that assures us that we follow strict guidelines for the installation of our products. This guarantees customers insurance companies, customers, and law enforcement agencies that installations are carried out safely and correctly.